Winkelgehäuse, Messanschluss

Function

Function for KK6
Port Designators [ + ]
Modifiers Ports
KK6, /10, /11, /S, /S3 Port 1: 1 1/2" Code 62; Port 2: 1 1/2" Code 62; Port 3: SAE 6; Gage Port: 1/4" NPTF;
KK6/1A, /1B, /M, /T, /T3 Port 1: 1 1/2" Code 62; Port 2: 1 1/2" Code 62; Port 3: 1/4" BSPP; Gage Port: 1/4" BSPP;
Technische Eigenschaften [ + ]
  • Alle Ventile, die für die T-19A Einschraubbohrung vorgesehen sind, passen auch in ein T-19AU Gehäuse.
Technische Daten [ + ]
Gehäusetyp RohrleitungseinbauRohrleitungseinbau
Lochbild SAE 1 1/2" - 6000 psiSAE 1 1/2" - 6000 psi
Gehäuseeigenschaften Winkelgehäuse, MessanschlussWinkelgehäuse, Messanschluss
Gewinde der Montagebohrung .375-16 UNC - 2B in..375-16 UNC - 2B in.
Gewinde der Montagebohrung M10x1.5 - 6H (metric models)M10x1.5 - 6H (metric models)
Montagebohrungstiefe .62 in.15,7 mm
Anzahl der Montagebohrungen 22
Einschraubbohrung T-19AU
Open Cavities 11
Anschlussgröße SAE 1 1/2" - 6000 psiSAE 1 1/2" - 6000 psi
FAQs [ + ]

Es sind genau 250 "SUN" Tropfen in einem cubic inch oder 15 in einem ccm.

Reasons to anodize:

  • To increase corrosion resistance. Sun uses 6061-T651 aluminum. It is one of the most corrosion resistant aluminum alloys there is. Whether or not anodizing improves the corrosion resistance of 6061 aluminum is debatable. We have yet to have a manifold returned because of corrosion.
  • Appearance (color). The 2 colors that would appeal to Sun would be blue or black. Unfortunately these are the colors that are hardest to do consistently.
  • To provide a hard wear surface. Sun does not make parts-in-body valves. The manifold is just plumbing. We don't need a wear surface.
  • Because everyone else does it. Bad reason. 

Reasons to not anodize:

  • Cost. It's another process.
  • Logistics. When you make tens of thousands of manifolds a month and you anodize hundreds, it's a problem. Consistency. See above.
  • Stamping. After a body is anodized you cannot do any more stamping without making a mess.
    Inspection. Have you ever tried to look for burrs in a black anodized body? It's the old blackboard factory at night scenario.
  • Torque. You will experience an increase in breakaway torque when removing items from an anodized manifold.
  • Fatigue life. This is the best reason to not anodize. Fatigue failure is a very complex phenomenon. What it takes to initiate a crack is difficult to predict. What it takes to propagate a crack is readily defined. Anodizing produces a very thin, very hard, and very brittle surface on aluminum. The first time you pressurize an anodized aluminum manifold you have initiated fatigue cracks. Whether or not the stress is enough to propagate the cracks is a matter of pressure and manifold geometry. Anodizing an aluminum manifold grossly reduces the fatigue life by anywhere from 20% to 50%.
Info [ + ]
  • Wichtig: Beachten Sie bitte sorgfältig die maximalen Systemdrücke, denen das Gehäuse ausgesetzt ist. Der Druckbereich ist hauptsächlich abhängig vom Gehäusematerial. Anschlussart und Anschlussgröße sind von sekundärer Bedeutung. Aluminiumgehäuse sind nur bis zu einem Systemdruck von 210 bar zugelassen, während Graugussgehäuse bis 350 bar belastet werden dürfen.
Zusätzliche Hilfsmittel [ + ]