Régulateur de débit réglable pleine plage, compensé en pression, avec clapet de by-pass

Capacité: 50 gpm200 L/min. | Cavité: T-18A
FDFA : Régulateur de débit réglable pleine plage, compensé en pression, avec clapet de by-pass
Caractéristiques techniques [ + ]

Les régulateurs de débit compensés en pression avec clapet de by-pass, réglables sur la totalité de la plage, fonctionnent en entrée ou en sortie de récepteur et assurent une régulation précise du débit même en cas d'importantes fluctuations de la pression. Ils permettent une infinité de réglages depuis la quasi fermeture jusqu'au débit maximum. Un clapet anti-retour de grande capacité laisse passer le débit sans restriction de la chambre 2 vers la chambre 1.

  • Toutes les cartouches de contrôle de débit à 2 orifices, sont physiquement et fonctionnellement interchangeables (c’est-à-dire le même sens de débit, la même cavité pour une taille donnée). Cependant, les dimensions extérieures de la cartouche peuvent varier.
  • Le dispositif de réglage compensé en pression permet un réglage facile même à haute pression.
  • Le gicleur à paroi mince minimise les variations de débit dues aux variations de viscosité.
  • La fuite minimum est de 0,8 L/min (.2 gpm) lorsque le mécanisme de réglage est tourné dans la position fermée.
  • Les cartouches configurées avec des joints EPDM s’utilisent dans les systèmes avec des fluides ester phosphate. L’exposition de ces joints à des fluides à base de pétrole, de graisse ou de lubrifiant détériorera les joints.
Caractéristiques [ + ]
Remarque: Les caractéristiques peuvent changer selon la configuration. Voir la section CONFIGURATION.
Cavité T-18A
Taille 4
Capacité 50 gpm200 L/min.
Pression maximale de fonctionnement 5000 psi350 bar
Adjustment - No. of CCW Turns from Fully Closed to Fully Open 55
Dimensions du six pans de la valve 1"5/8 in.41,3 mm
Couple de serrage de la valve 350 - 375 lbf ft474 - 508 Nm
Taille du 6 Pans Creux de la Vis de Réglage 5/32 in.4 mm
Dimension du contre-écrou sur plat 9/16" in.15 mm
Couple de serrage du contre écrou 80 - 90 lbf in.9 - 10 Nm
Poids du composant 3,30 lb1,50 kg
Seal kit - Cartridge Buna: 990018007
Seal kit - Cartridge EPDM: 990018014
Seal kit - Cartridge Polyurethane: 990018002
Seal kit - Cartridge Viton: 990018006
Performance Curves [ + ]
FAQs [ + ]

I am afraid not. Unless you are overflowing your current valve and correctly size ours, you are not likely to notice any improvement. Priority flow controls are not efficient devices. They are an easy way to get more than 1 source of oil from 1 pump but they can generate a lot of heat. Try to size your actuators so the pressures are similar on both the priority and the bypass circuits. If you can't do that, try to have the lower flow leg be the lower pressure. The pump pressure is determined by whichever leg is higher and if there is flow that is taking a pressure drop that is not doing work it is creating heat.

All flow is blocked, hence the term priority. The priority flow has to be satisfied.

The valve acts as a 2 port restrictive flow control.

The spring force in our flow controls equates to about 100 psi (7 bar). This is high enough to give the valves acceptable capacity and not too high for proper circuit operation. 100 psi (7 bar) is the spring force; at the upper end of the flow control's range, the drop through the valve will be as high as 250 psi (17 bar) before it starts modulating.

Il y a exactement 15 gouttes Sun dans un centimètre cube.

In a meter-in flow control circuit if the pump is set at 3000 psi and the load is 2000 psi the drop through the flow control is 1000 psi. In a meter-out circuit with the load at 2000 psi the drop through the flow control is 2000 psi.

We claim +/- 10%. We set to +/- 5% in production testing to allow for differences in customers' conditions. If you want accuracy, stay in the bottom 2/3rds of the range. Our 12 gpm (45 L/min.) flow controls are quite flat at 9 gpm (34 L/min.) and dead flat below 6 gpm (23 L/min.), until you get to the bottom of the range. Below about .25 gpm (1 L/min.), spool leakage and orifice conditions start to limit accuracy.

Only external seals are serviceable.  Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.
Ressources Complémentaires [ + ]