2位, 6通, 电磁滑阀换向阀

流量: 5 gpm20 L/min. | 插孔: T-61A
DNDY : 2位, 6通, 电磁滑阀换向阀
技术特性 [ + ]

此类2位6通电磁阀为直动式,平衡滑阀结构。此阀的典型应用为在两个独立的油路中做选取。失电时P和T接通到第一个油路而得电时P和T接通到第二个油路。

  • 电磁铁组件的疲劳耐压等级为5000 psi (350 bar)。
  • 此阀可被直接驱动且不需要最小液压操作压力。
  • 此阀有几种不同的手动紧急操作选项,包括无手动紧急操作。见以下可选选项。请注意:风雨线圈不兼容手动紧急操作功能。
  • 配置EPDM密封圈的插装阀可用在磷酸酯液压油系统。暴露在石油基液压油或润滑油脂中会损坏密封圈。
  • 带D或L控制的型号,手动重载中的止动机构是用来作临时驱动用途。
  • 此阀采用湿式衔铁线圈设计。这意味着衔铁周围的工作流体介质将曝露在线圈所产生热场中。如果线圈长时间通电,这将是一个影响因素。一些液体,特别是水/乙二醇混合物,会在长时间高温下分解并形成凡立水,而这将会影响阀的功能。
  • 不同的线圈接头与电压选项都是可选的,也同时可选带或不带浪涌保护。
  • 线圈的独特电磁设计使电磁阀有更高的效率,单位瓦特产生高的阀芯驱动力,从而使阀有可靠的切换。
  • 线圈可以和Sun的系列1电磁阀产品互换并可从另外一个方向上安装在套筒上。
  • 线圈接头等级可提供至IP69K。请见单个线圈产品的详细产品说明。额外的风雨线圈和工具包可提供更完善的环境防护。
  • 利用Sun浮动结构减少由于过量安装扭矩或插孔/插装阀加工误差带来的内部零件粘结的可能性。
技术数据 [ + ]
注意:技术参数可能因产品配置而不同。请查看产品配置部分。
插孔 T-61A
系列 1
通流能力 5 gpm20 L/min.
最大操作压力 5000 psi350 bar
110 SUS (24 cSt)下的最大泄漏 5 in³/min.@3000 psi80 cc/min.@210 bar
手动紧急操作需要的力 5 lbs/1000 psi @ Port 133 N/100 bar @ Port 1
手动紧急操作动作行程 .10 in.2,5 mm
额定响应时间 50 ms50 ms
切换频率 15,000 max. cycles/hr15,000 max. cycles/hr
衔铁直径 .75 in.19 mm
阀头部安装六角尺寸 7/8 in.22,2 mm
阀安装扭矩 30 - 35 lbf ft41 - 47 Nm
型号重量 .60 lb0,30 kg
Seal and nut kit - Coil Viton: 990770006
Seal kit - Cartridge Buna: 990461007
Seal kit - Cartridge EPDM: 990461014
Seal kit - Cartridge Viton: 990461006
性能曲线 [ + ]
常见问题 [ + ]

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Only external seals are serviceable.  Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.
备注 [ + ]
  • 当选择Sun阀块时,请检查插装阀的间隙要求。不同的阀控制方式以及线圈要求的间隙不一样。
  • 在阀的最大尺寸之外需增加额外的2.00 inches (50,8 mm),以进行线圈的安装和移除。
额外来源 [ + ]
Coil Information [ + ]

No coil selected.