顺序 安装组件 , with reverse flow check

Function

Function for YQHA
Port Designators [ + ]
Modifiers Ports
D, D/S Ports 1 & 2: 3/4" NPTF; Port 3: 1/4" NPTF; Gage Port: 1/4" NPTF;
E, E/S Ports 1 & 2: 1" NPTF; Port 3: 1/4" NPTF; Gage Port: 1/4" NPTF;
F, F/S Ports 1 & 2: 1 1/4" NPTF; Port 3: 1/4" NPTF; Gage Port: 1/4" NPTF;
L, L/S Ports 1 & 2: SAE 12; Port 3: SAE 6; Gage Port: 1/4" NPTF;
M, M/S Ports 1 & 2: SAE 16; Port 3: SAE 6; Gage Port: 1/4" NPTF;
N, N/S Ports 1 & 2: SAE 20; Port 3: SAE 6; Gage Port: 1/4" NPTF;
P, P/S Ports 1 & 2: 1" Code 61; Port 3: SAE 6; Gage Port: 1/4" NPTF;
P/M, P/T Ports 1 & 2: 1" Code 61; Port 3: 1/4" BSPP; Gage Port: 1/4" BSPP;
Q, Q/S Ports 1 & 2: 1 1/4" Code 61; Port 3: SAE 6; Gage Port: 1/4" NPTF;
Q/M, Q/T Ports 1 & 2: 1 1/4" Code 61; Port 3: 1/4" BSPP; Gage Port: 1/4" BSPP;
W, W/S Ports 1 & 2: 3/4" BSPP; Port 3: 1/4" BSPP; Gage Port: 1/4" BSPP;
X, X/S Ports 1 & 2: 1" BSPP; Port 3: 1/4" BSPP; Gage Port: 1/4" BSPP;
Y, Y/S Ports 1 & 2: 1 1/4" BSPP; Port 3: 1/4" BSPP; Gage Port: 1/4" BSPP;
技术特性 [ + ]

This assembly consists of a pilot-operated, balanced piston kick-down sequence valve that will kick completely open and remain open once the pressure at the inlet (port 1) exceeds the valve setting, creating an unrestricted flow path from port 1 to port 2 (sequence). The pressure setting at port 1 is relative to the drain (port 3). The valve remains open as long as the pressure at port 1 exceeds the pressure at port 2. To reset the valve, pressure at port 1 must fall below the setting of the valve, flow from port 1 to port 2 must cease, and pressure at port 2 must be equal to or greater than the pressure at port 1. Additionally a reverse flow check allows free flow from port 2 to 1.

  • Should not be used in load holding applications.
  • Intended for use on the actuator side of the system as flow through the valve must cease for the valve to reset. If used on the pump side of a system, pump flow must be shut off for the valve to reset.
  • Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi (350 bar).
技术数据 [ + ]
阀块类型 管式安装管式安装
通流能力 60 gpm240 L/min.
常见问题 [ + ]

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

Reasons to anodize:

  • To increase corrosion resistance. Sun uses 6061-T651 aluminum. It is one of the most corrosion resistant aluminum alloys there is. Whether or not anodizing improves the corrosion resistance of 6061 aluminum is debatable. We have yet to have a manifold returned because of corrosion.
  • Appearance (color). The 2 colors that would appeal to Sun would be blue or black. Unfortunately these are the colors that are hardest to do consistently.
  • To provide a hard wear surface. Sun does not make parts-in-body valves. The manifold is just plumbing. We don't need a wear surface.
  • Because everyone else does it. Bad reason. 

Reasons to not anodize:

  • Cost. It's another process.
  • Logistics. When you make tens of thousands of manifolds a month and you anodize hundreds, it's a problem. Consistency. See above.
  • Stamping. After a body is anodized you cannot do any more stamping without making a mess.
    Inspection. Have you ever tried to look for burrs in a black anodized body? It's the old blackboard factory at night scenario.
  • Torque. You will experience an increase in breakaway torque when removing items from an anodized manifold.
  • Fatigue life. This is the best reason to not anodize. Fatigue failure is a very complex phenomenon. What it takes to initiate a crack is difficult to predict. What it takes to propagate a crack is readily defined. Anodizing produces a very thin, very hard, and very brittle surface on aluminum. The first time you pressurize an anodized aluminum manifold you have initiated fatigue cracks. Whether or not the stress is enough to propagate the cracks is a matter of pressure and manifold geometry. Anodizing an aluminum manifold grossly reduces the fatigue life by anywhere from 20% to 50%.
备注 [ + ]
  • Important: Carefully consider the maximum system pressure. The pressure rating of the manifold is dependent on the manifold material, with the port type/size a secondary consideration. Manifolds constructed of aluminum are not rated for pressures higher than 3000 psi (210 bar), regardless of the port type/size specified.
  • For detailed information regarding the cartridges contained in this assembly, click on the models codes shown in the Included Components tab.
额外来源 [ + ]