Configurable double-output driver used con proporcional y solenoid-operated switching valves
The XMD module is an electro-hydraulic driver for use with mobile and industrial hydraulic equipment. It is configurable using Sun's free CANpoint XMD Configuration Software and a CAN-to-USB interface cable connected to a computer or via the XMD Mobile app. The XMD driver can control a variety of electrically operated hydraulic actuators used in applications for on- and off-highway equipment including but not limited to agriculture, forestry, construction, marine, earth moving, and material handling. Tuned for optimal flow and pressure control using Sun valves, the XMD driver delivers repeatable and reliable results for your demanding applications.
- Dual-coil driver
- Two configurable 0-5 V, 0-10 V, 4-20 mA, pulse, frequency, PWM and digital inputs
- For full product details, including installation and operating instructions, refer to the Full Data Sheet link at the top of this page.
- CAN bus communication (SAE J1939)
- Adjustable current limited output with short circuit protection
- 5-V reference for potentiometer/joystick controls
- Configurable enable input
- All input and output limits are independently adjustable
- Adjustable ramp up and ramp down times, independently set
- Microprocessor controlled for consistent, reliable performance
- Separate supply and command common
- High-frequency PWM with superimposed dither
- Glass-filled nylon enclosure with flexible potting compound
- Setup and configuration can be accomplished through the CANpoint XMD Configuration Software and a CAN-to-USB interface cable or via Sun's XMD Mobile™ app with a Bluetooth connection from a smartphone.
- Rated at IP69k
- CE and E-Mark approved
- Power cable with mating connector is required and is not included with product. Refer to the "Used With" tab.
|Supply Voltage||9-32 VDC9-32 VDC|
|Supply Current||6 Amps max.6 Amps max.|
|Number of Outputs||22|
|Output Types||PWM and Duty Cycle (0-100%)PWM and Duty Cycle (0-100%)|
|Output Current||0 to 3000 mA0 to 3000 mA|
|Current Regulation||± 1 mA above 35 mA± 1 mA above 35 mA|
|PWM Frequency||33-5,000 Hz33-5,000 Hz|
|Dither Frequency||33-500 Hz33-500 Hz|
|Dither Amplitude||0-25% of Imax0-25% of Imax|
|Ramp Time||0-65.0 s, 1 ms increments0-65.0 s, 1 ms increments|
|Number of Universal Inputs||22|
|Input Range||0-5V, 0-10V, 4-20 mA, digital, pulse (60 Hz-10 kHz), PWM (60 Hz-10 kHz), resistive (0-100 kΩ)0-5V, 0-10V, 4-20 mA, digital, pulse (60 Hz-10 kHz), PWM (60 Hz-10 kHz), resistive (0-100 kΩ)|
|Reference Voltage||5 Vdc, ±0.1 Vdc (250 mA max)5 Vdc, ±0.1 Vdc (250 mA max)|
|CAN Communication||CAN 2.0B (Maximum voltage + 32 Vdc)CAN 2.0B (Maximum voltage + 32 Vdc)|
|CAN Protocols||SAE J1939SAE J1939|
|Baud Rates||125 kbit/s, 250 kbit/s, 500 kbit/s, 1 Mbit/s125 kbit/s, 250 kbit/s, 500 kbit/s, 1 Mbit/s|
|Mating Connector||Deutsch DT06-12SA-XXXDeutsch DT06-12SA-XXX|
|Operating Temperature Range||-40 - 85 °C-40 - 85 °C|
|Storage Temperature Range||-60 - 120 °C-60 - 120 °C|
|Vibration||33.3 Hz 6.8g Peak (Spec: S-367 Section 11.0)33.3 Hz 6.8g Peak (Spec: S-367 Section 11.0)|
|Shock||49g Peak (Spec: S-367 Section 12.0)49g Peak (Spec: S-367 Section 12.0)|
|Enclosure||Enclosure PBT, 30 % glass-filledEnclosure PBT, 30 % glass-filled|
|Product Dimensions (L x W x H)||3.38 x 2.30 x 1.40 in.85,9 x 58,5 x 35,6 mm|
|Certification||CE, E-Mark, E11 10R-05100024 2014/53/EU (Radio Equipment Directive), 2014/35/EU (Low Voltage Directive)CE, E-Mark, E11 10R-05100024 2014/53/EU (Radio Equipment Directive), 2014/35/EU (Low Voltage Directive)|
|EMC/EMI||EN 55024, EN 55032, EN 13309, EN/ISO 14982, ISO 13766, ISO 16750-2, J1113-4/11/12/13/26,ISO 1142-2/10, CISPR 25, FCC 15B, ICES-003, UNECE Reg 10.5, EN 61326-1:2013, EN 301 489-1, V2.2.0, EN 301 489-17, EN 12895EN 55024, EN 55032, EN 13309, EN/ISO 14982, ISO 13766, ISO 16750-2, J1113-4/11/12/13/26,ISO 1142-2/10, CISPR 25, FCC 15B, ICES-003, UNECE Reg 10.5, EN 61326-1:2013, EN 301 489-1, V2.2.0, EN 301 489-17, EN 12895|
|U.S. Patent #||PendingPending|
Yes, up to 3 amps per PWM output. This includes pumps, CETOP valves, directional valves, proportional valves, and more. Duty-cycle mode can also control solenoid switching valves, PWM variable speed e-Fans and LEDs.
See page 4 of the XMD Mobile App User Guide for compatible devices. This Guide can be found in "Additional Resources" section of the XMD webpage.
Two-wire resistive input devices will pull excitation voltage from the input pin. Only two wires are needed for this input type — one connected to the XMD input pin and one connected to an external ground.
Call Sun at +1 941-362-1200.
No. The resistance values for each coil voltage are selected to limit the maximum current that can be drawn by the coil. A mismatch in coil and supply voltage can result in too little or too much current draw. A coil should be selected based on supply voltage being used.
XMD-02: I(sol1) + I(sol2) + 25mA
XMD Series Drivers include a TVS Diode. Coils do not need a diode when being controlled by an XMD driver.
The XMD default settings have the enable function turned on. In order to see any output, at least 3VDC must be sent to pin 9, the enable pin. Alternatively, the enable function can be disabled on the config screen of the XMD app.
What models can this kit be used with?
- 991711300 XMD Series, 12-pin Deutsch prototype , single-output - 3M
- 991711600 XMD Series, 12-pin Deutsch prototype , single-output - 6M
- 991712300 XMD Series, 12-pin Deutsch prototype , double-output - 3M
- 991712600 XMD Series, 12-pin Deutsch prototype , double-output - 6M
- 991713030 XMD Series, 2-pin Deutsch prototype - 30CM
- 991713060 XMD Series, 2-pin Deutsch prototype - 60CM
- 991720300 XMD Series, 3M, 12-pin Deutsch prototype , single-output con 2-pin Deutsch lead
- 991720600 XMD Series, 6M, 12-pin Deutsch prototype , single-output con 2-pin Deutsch lead
- 991721300 XMD Series, 3M, 12-pin Deutsch prototype , single-output con ISO/DIN 43650, Form A lead
- 991721600 XMD Series, 6M, 12-pin Deutsch prototype single-output con ISO/DIN 43650, Form A lead
- 991722 12-pin Deutsch conector juego
- 991723001 2-pin Deutsch conector juego (gray)
- 991723002 2-pin Deutsch conector juego (black)
- 991728 XMD Series CAN-to-USB hardware interface
- 991740001 XMD Series, high-power coil clip juego
- 991740002 XMD Series, low-power coil clip juego
- 991770001 XMD Series, Serie 770 coil clip
- Installation bracket and mounting hardware are included. Coil clips for high and low-power FLeX Series coils are sold separately.
- Electrohidráulica optimizada y ajustada de fábrica desde el primer momento
- XMD: Sun's compact, Bluetooth & CAN bus configurable electro-hydraulic driver
- Software de configuración CANpoint XMD
- CE Declaration of Conformity - XMD 12-2017 (133.69 KB)
- XMD Installation Guide - 01/02 (892.83 KB)
- CANpoint Quick Start Guide (3.6 MB)
- XMD Mobile App User Guide (10.31 MB)
- Electro-Hydraulic Solutions (3 MB)
- XMD Coil Clip Installation Guide (749.23 KB)