Montage direct, pilotages croisés


Function for YVQ
Port Designators [ + ]
Modifiers Ports
YVQ, /10, /11, /15, /16, /1A, /1B, /1F, /1G, /M, /V, /Z Ports C2, V1, V2: SAE 16;
Caractéristiques [ + ]
Type de Corps Montage flasquéMontage flasqué
Plan de Pose SunSun
Caractéristiques du Corps Montage direct, pilotages croisésMontage direct, pilotages croisés
Diamètre des Trous de Fixation .50 in. (metric models)12,7 mm (metric models)
Diamètre des Trous de Fixation 0,53 in.13,5 mm
Profondeur des Trous de Fixation TraversantTraversant
Diamètre du Lamage des Trous de Fixation .75 in. (metric models)19 mm (metric models)
Diamètre du Lamage des Trous de Fixation 0,78 in.19,8 mm
Profondeur du Lamage des Trous de Fixation .44 in. (metric models)11,1 mm (metric models)
Profondeur du Lamage des Trous de Fixation 0,44 in.11,1 mm
Nombre de Trous de Fixation 22
Cavité T-17A
Open Cavities 22
Taille de l'Orifice 1"5/16-12UNF1"5/16-12UNF
FAQs [ + ]

Il y a exactement 15 gouttes Sun dans un centimètre cube.

Reasons to anodize:

  • To increase corrosion resistance. Sun uses 6061-T651 aluminum. It is one of the most corrosion resistant aluminum alloys there is. Whether or not anodizing improves the corrosion resistance of 6061 aluminum is debatable. We have yet to have a manifold returned because of corrosion.
  • Appearance (color). The 2 colors that would appeal to Sun would be blue or black. Unfortunately these are the colors that are hardest to do consistently.
  • To provide a hard wear surface. Sun does not make parts-in-body valves. The manifold is just plumbing. We don't need a wear surface.
  • Because everyone else does it. Bad reason. 

Reasons to not anodize:

  • Cost. It's another process.
  • Logistics. When you make tens of thousands of manifolds a month and you anodize hundreds, it's a problem. Consistency. See above.
  • Stamping. After a body is anodized you cannot do any more stamping without making a mess.
    Inspection. Have you ever tried to look for burrs in a black anodized body? It's the old blackboard factory at night scenario.
  • Torque. You will experience an increase in breakaway torque when removing items from an anodized manifold.
  • Fatigue life. This is the best reason to not anodize. Fatigue failure is a very complex phenomenon. What it takes to initiate a crack is difficult to predict. What it takes to propagate a crack is readily defined. Anodizing produces a very thin, very hard, and very brittle surface on aluminum. The first time you pressurize an anodized aluminum manifold you have initiated fatigue cracks. Whether or not the stress is enough to propagate the cracks is a matter of pressure and manifold geometry. Anodizing an aluminum manifold grossly reduces the fatigue life by anywhere from 20% to 50%.
Notes [ + ]
  • Important: Il est indispensable de connaître la pression maximum du système dans lequel le bloc sera intégré. La pression maxi de fonctionnement du bloc dépend de la matière du bloc, alors que le type et la taille des orifices sont secondaires. Par exemple, les blocs fabriqués en aluminium ne sont pas conçus pour des systèmes où la pression est supérieure à 210 bar, quels que soient le type et la taille des orifices.
Ressources Complémentaires [ + ]