2-way, pilot shifted, dual path, proportional throttle with position switch
This valve is a 2-way, 2-position proportional throttle. Ports 2 and 3 are normally closed. Pilot pressure at port 1 creates a metering orifice between port 2 and 3 that is proportional to the pressure at 1. The metering passage is self-compensating.
This valve uses a dual-path design. Ports 2 and 3 incorporate a double-port area.
This valve incorporates a position switch to provide confirmation that the valve is closed.
- This cartridge is supplied as a sealed, factory set unit and is not field serviceable. Any tampering will violate the product warranty.
- Position switch is CE approved.
- When torquing this cartridge into its cavity, a crow's foot wrench or similar will be required since the position switch precludes the use of a deep socket wrench.
- These valves may be pressure compensated by an external, modulating, logic element. Use LR_C-XHN for a bypass circuit or LP_C-XHN for a restrictive circuit.
- The valve provides a degree of self-compensation and may be used as a flow control. To increase the accuracy of flow control, an external, modulating, logic element can be used to maintain a constant flow over a wider range of flows and pressures. See performance curves for additional information.
- An optional protective cover, with mounting hardware included, may be ordered separately. See kit number: 991-043.
- Ports 1 and 4 should be limited to 500 psi (35 bar).
- Pressure at port 4 directly opposes pressure at port 1.
- Accurate pressure compensated control requires that a constant pressure differential be maintained across the valve.
- Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.
|Capacity||15 gpm60 L/min.|
|Pilot Pressure Required to Shift Valve||60 - 130 psi4 - 9 bar|
|Pilot Pressure Required for Full Shift at Rated Flow||290 - 340 psi20 - 23 bar|
|Maximum Operating Pressure||5000 psi350 bar|
|Maximum Valve Leakage at 110 SUS (24 cSt)||5 in³/min.@1000 psi80 cc/min.@70 bar|
|Pilot Volume Displacement||.05 in³0,82 cc|
|Valve Hex Size||1 1/8 in.28,6 mm|
|Valve Installation Torque||45 - 50 lbf ft61 - 68 Nm|
|Model Weight||1.90 lb0,85 kg|
|Seal kit - Cartridge||Buna: 990152007|
|Seal kit - Cartridge||Viton: 990152006|
|Supply Voltage||20-30 VDC20-30 VDC|
|Operating Temperature Range||-25 to 80 °C-25 to 80 °C|
|Vibration||≥ 50g, 0-500 impulses/sec≥ 50g, 0-500 impulses/sec|
|Shock||>50 g, 1ms>50 g, 1ms|
|Reverse Polarity Protection||YesYes|
|Maximum Output Load||≤ 400 mA, Duty Ratio 100%≤ 400 mA, Duty Ratio 100%|
|Short Circuit Protection||Yes, Load Short UnlimitedYes, Load Short Unlimited|
|Turn On Time||≤ 25 ms≤ 25 ms|
|Hysteresis||35 %35 %|
|Thermal Shift - 0 to 80 °C ≤ ±||.004 in.0,1 mm|
|EMC||DIN EN 61000-6-1/2/3/4DIN EN 61000-6-1/2/3/4|
|Connector||M12 X 1 (4) PinM12 X 1 (4) Pin|
|Connector Environment Rating||IP65IP65|
There are exactly 250 Sun drops in a cubic inch or 15 in a cc.
- When installed in Sun's standard T-52A line mount manifold, plug unused ports and expect higher pressure drops.
- High Capacity Electro-Proportional Throttle Valve
- Sun Expands Corrosion-Resistant Solutions
- QuickDesign with SmartConnect Offers Drag-and-Drop Schematic Tool
- Series 4 PLUS Cartridges Offer Higher Flows with Lower Pressure Losses
- Sun Offers Zinc-Nickel Plating for Corrosion Resistance
- Sun Cartridges with EPDM Seals
- Manufacturing Sun Cartridge Cavities (522.27 KB)
- Fluid Recommendations: Oil Viscosity, Cleanliness & Temperature
- Sun's Floating Style Screw-In Cartridge (1.06 MB)
- Performance Data
- Sun Model Code Explanation; 999-901-334 (343.9 KB)
- Units of Measure, Settings, and Conversions
- Cartridges: Materials of Construction
- Cavity Information (S-171) and Tooling
- CE Declaration of Conformity - XMD 12-2017 (133.69 KB)