Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

24 VDC 防爆线圈, 双出线, 1/2" NPT 导管接头, ATEX和IECEx认证

全部展开

技术特性 [ + ]

Sun可以提供用在恶劣环境中的防爆电磁阀。线圈不能单独订购而须和插装阀一起配置订购。关于订购信息，请参考阀件产品页面的线圈选项部分。

Atex防爆认证，Ex mb IIC T3 Gb II 2 G 0518 IP67
IECEx certified: Ex mb IIC T3 Gb (See Additional Resources tab below)
此线圈符合CE认证。
认证需要防爆线圈以完整阀件/线圈安装体来卖出。线圈不能单独采购。
为达到最好的比例控制效果，需要采用电流控制以及颤振控制的比例放大器。颤振频率可调范围为100-250Hz。
IP等级为IP67.
符合欧盟RoHS标准。有害成分质量少于0.1%。
外部铁壳的镀层为锌以及黄色重铬酸盐。
整体的过热以及过电流熔断器保护。
线圈内无电弧抑制二极管。
绕线是采用NEMA-MW-80, 等级F (155摄氏度)的漆包线。
为达到正确的性能，线圈须以正确的方位安装在阀件上。请参考示意图/指示。

回到首页

比例性能数据 [ + ]

最大电流	590 mA590 mA

回到首页

技术数据 [ + ]

环境温度范围	-58 to 104 °F-58 to 104 °F
电量消耗（低温）- 在相关的电压下	22 watts22 watts
额定电流	0.93 amps at 68ºF (20ºC), 24 VDC0.93 amps at 68ºF (20ºC), 24 VDC
线圈直径要求的空隙	2.125 in.53,98 mm
电压/频率	24 VDC24 VDC
运行电压范围	+/- 10% nominal+/- 10% nominal
电流保险丝（不可调）	3 amps3 amps
热保险 (不可重设)	378 °F192 °C
寿命测试等级	100 %100 %
接头	Twin lead 18 AWG X 10 ft. (3 m), 1/2-14 NPT female conduit connectorTwin lead 18 AWG X 10 ft. (3 m), 1/2-14 NPT female conduit connector
接头防护等级	IP67IP67
绕线等级	AWM styles 3289 150°C - 3271 125°C, 600V VW-1 LL30433 CSA CL1251 125°C or CL1503 150°C, XLPE 600V 18 AWGAWM styles 3289 150°C - 3271 125°C, 600V VW-1 LL30433 CSA CL1251 125°C or CL1503 150°C, XLPE 600V 18 AWG
衔铁直径	.75 in.19 mm
线圈锁紧螺母扭矩	6 - 7 lbf ft8 - 9,5 Nm
型号重量	1.60 lb0,70 kg