2通, 2级, 电磁锥阀换向阀 - 流量 2到1

流量: 30 gpm120 L/min. | 插孔: T-5A
DFDB : 2通, 2级, 电磁锥阀换向阀 - 流量 2到1
技术特性 [ + ]

此类2位2通电磁阀为先导控制式,锥阀结构且带反向自由流单向阀。此阀有常开与常闭两种配置。此阀为锥阀芯结构,因此具有极低的泄漏。

  • 电磁铁组件的疲劳耐压等级为5000 psi (350 bar)。
  • 配置EPDM密封圈的插装阀可用在磷酸酯液压油系统。暴露在石油基液压油或润滑油脂中会损坏密封圈。
  • 阀表现出极低的泄漏速率;小于10滴/分钟。@5000 psi(0,7 cc/min @ 350 bar)。
  • 此阀有几种不同的手动紧急操作选项,包括无手动紧急操作。见以下可选选项。请注意:风雨线圈不兼容手动紧急操作功能。
  • 带D或L控制的型号,手动重载中的止动机构是用来作临时驱动用途。
  • 此阀采用湿式衔铁线圈设计。这意味着衔铁周围的工作流体介质将曝露在线圈所产生热场中。如果线圈长时间通电,这将是一个影响因素。一些液体,特别是水/乙二醇混合物,会在长时间高温下分解并形成凡立水,而这将会影响阀的功能。
  • 不同的线圈接头与电压选项都是可选的,也同时可选带或不带浪涌保护。
  • 线圈的独特电磁设计使电磁阀有更高的效率,单位瓦特产生高的阀芯驱动力,从而使阀有可靠的切换。
  • 线圈可以和Sun的系列1电磁阀产品互换并可从另外一个方向上安装在套筒上。
  • 线圈接头等级可提供至IP69K。请见单个线圈产品的详细产品说明。额外的风雨线圈和工具包可提供更完善的环境防护。
  • Sun浮动式的结构可以最大限度地减少由于过大的安装扭矩以及孔型加工的误差所造成的干涉现象。
技术数据 [ + ]
注意:技术参数可能因产品配置而不同。请查看产品配置部分。
插孔 T-5A
系列 2
通流能力 30 gpm120 L/min.
最大操作压力 5000 psi350 bar
110 SUS (24 cSt)下的最大泄漏 10 drops/min.@5000 psi0,7 cc/min.@350 bar
单向开启压力 50 psi3,5 bar
额定响应时间 30 ms30 ms
切换频率 15,000 max. cycles/hr15,000 max. cycles/hr
衔铁直径 .75 in.19 mm
阀头部安装六角尺寸 1 1/8 in.28,6 mm
阀安装扭矩 45 - 50 lbf ft61 - 68 Nm
型号重量 .70 lb0,30 kg
Seal kit - Cartridge Buna: 990203007
Seal kit - Cartridge EPDM: 990203014
Seal kit - Cartridge Viton: 990203006
性能曲线 [ + ]
常见问题 [ + ]

Direct acting valves are used to prevent over pressure and pilot operated valves are used to regulate pressure. If you are unsure, use a direct acting valve. Sun's direct acting valves are very fast, dirt tolerant, stable, and robust. Sun's pilot operated valves are moderately fast, they have a low pressure rise vs. flow curve, and they are easy to adjust.

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

In many circuits the directional cartridge is set to shift at a low pressure no matter how high the pilot pressure goes. If you use a DP__ , the pilot flow increases to significant amounts. A DR__ however will only consume a small amount of flow. A DP__ is useful when you want to block or open the pilot flow to shift the valve.

Only external seals are serviceable.  Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.
备注 [ + ]
  • 当选择Sun阀块时,请检查插装阀的间隙要求。不同的阀控制方式以及线圈要求的间隙不一样。
  • 在阀的最大尺寸之外需增加额外的2.00 inches (50,8 mm),以进行线圈的安装和移除。
额外来源 [ + ]
Coil Information [ + ]

No coil selected.