Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

T-10A插孔至 T-8A插孔转换器

流量: | 插孔: T-10A

全部展开

技术特性 [ + ]

Sun提供很多可选的转换接头。XFAA孔型转换接头可以将Sun的T-10A的孔型转换为Sun的T-8A的孔型。这种结构是被使用在替换场合，例如，Sun的RBAC-***，先导控制溢流阀就可以被Sun的RBAP-***，比例先导控制溢流阀或者其它T-8A的阀所替代

配置EPDM的插装阀用于磷酸酯油液压系统。该密封若暴露在石油基液压油或润滑油，润滑脂中，将会被损坏。

回到首页

技术数据 [ + ]

注意：技术参数可能因产品配置而不同。请查看产品配置部分。

插孔	T-10A
系列	1
最大操作压力	5000 psi350 bar
先导控制孔型	T-8AT-8A
阀头部安装六角尺寸	7/8 in.22,2 mm
阀安装扭矩	30 - 35 lbf ft41 - 47 Nm
Seal kit - Cartridge	Buna: 990010007
Seal kit - Cartridge	EPDM: 990010014
Seal kit - Cartridge	Polyurethane: 990010002
Seal kit - Cartridge	Viton: 990010006

回到首页

常见问题 [ + ]

How big is a drop of hydraulic oil?

There are exactly 250 Sun drops in a cubic inch or 15 in a cc.

What parts of the Sun cartridge valve are field serviceable?

Only external seals are serviceable. Sun offers replacement seal kits for all cartridge models. The applicable kit part number can be found in the product page's Technical Data table or by using our Cartridge Seal Kit search function located under Accessories. Please note: Converting the external seals from one material to another does not ensure fluid compatibility with that material due to the existence of internal seals within the cartridge.

回到首页

额外来源 [ + ]

集锦

技术指导

Sun插装阀插孔 (551.8 KB)
回路简化阀 (623.23 KB)

技术信息

回到首页

XFAA | 插装阀 » Specialty » 装换件 | Sun Hydraulics

Assembly Build Process

Assembly Build Process

T-10A插孔至 T-8A插孔转换器

Footer

T-10A插孔 至 T-8A插孔 转换器

Footer

T-10A插孔至 T-8A插孔转换器