Assembly Build Process

Sun's Assembly Build Process allows you to configure a cartridge and manifold, or main stage and pilot stage cartridge, and build a digital assembly in three dimensional space. The resulting output of this process is the assembly product page, including configuration-specific images, symbols, product information and CAD files for download.

The Assembly Build Process can be accessed from either a cartridge or manifold product page. Only valid choices are allowed.

From a manifold page, you must first choose your cartridge function. Once you choose your function, click on the BUILD ASSEMBLY button below the WHERE TO BUY BUTTON. Once clicked, you will be presented with valid cartridges for your manifold. Select the cartridge of your choice and follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

From a cartridge product page, click on BUILD ASSEMBLY and you will be presented with a listing of compatible manifolds. In the case of main stage and pilot stage cartridges, you can either build a cartridge to cartridge assembly or a cartridge to manifold assembly. Once your choice has been made, follow the instructions at the top of the page. If your particular combination has been generated before, the resulting assembly page will be available immediately. If not, you will be asked to enter your email address. Once the page is complete, an email will be sent to you including a link to the assembly product page.

Please note that the Assembly Build Process is an automated process. It can be utilized at any time. Pages are generated typically within minutes but delays can occasionally be expected. In the event of a delay, a team at Sun will work to resolve the issue to ensure you receive your information as quickly as possible.

740 Series, 28 VCC, low-power bobine avec ISO/DIN 43650, Forme A Connecteur without TVS Diode (XMD-02 driver included)

Développer

Caractéristiques techniques [ + ]

Coil windings utilize Class N, (392° F [200 °C] rated) magnet wire.
Power cable with mating connector is required and is not included with the coil.
The coil is magnetically symmetrical and can be mounted on the solenoid tube in either direction for best cable access without affecting performance.
Coil is fully RoHS compliant. Restricted materials less than 0.1% total by weight.
The external steel shell is zinc-nickel plated and provides 1000-hour salt fog protection.
For optimum proportional performance, an amplifier with current sensing and adjustable dither should be used. Dither should be adjustable between 100 - 250 Hz.
IP rating for this coil is IP65/IP67.
This coil does not include a transient voltage suppression (TVS) diode and should only be used when surge suppression is included elsewhere in the electrical system. If no surge suppression is included in the circuit, the coil version with TVS diode should be used.
This coil assembly includes the XMD-02 electro-proportional driver.

Retour Vers le Haut

Caractéristiques [ + ]

Plage de Température de fonctionnement	-40 to 230 °F-40 to 110 °C
Arc Suppression (TVS)	AucunAucun
Puissance consommée (à froid) - à une tension donnée	17 Watts17 Watts
Température Ambiante Maximum	212 °F100 °C
Resistance at 20º C	46.1 ohms ±10%46.1 ohms ±10%
Tension / Fréquence	28 VCC28 VCC
Plage de Tension de Fonctionnement	+10%/-15%+10%/-15%
Facteur de service	100 %100 %
Connecteur	ISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pinISO4400 - EN/DIN175301-803, Form A (ISO/DIN 43650) 3-pin
Diamètre du Doigt de Gant	0,62 in.15,7 mm
Couple de Serrage de l'Ecrou de la Bobine	4,5 lbf in.0,5 Nm
Poids du composant	12.4 oz.12.4 oz.

Retour Vers le Haut

FAQs [ + ]

What are the shock and vibration levels the 740 coils are capable of withstanding?

740 Series coils meet Sun specification S-367. This specification is on our website under Technical Resources and is also listed in the Additional Resources tab on applicable product pages. Please see sections 11 and 12 of Environmental Test Specification for Electrical and Electronic Components; S-367.

Retour Vers le Haut

Used With [ + ]

What models can this kit be used with?

FPBD FLeX Series pilot-operated, Normalement Fermé, électro-proportionnel Étrangleur - flow 2-1 - 3000 psi (210 bar)
FPBE FLeX Series pilot-operated, Normalement Fermé, électro-proportionnel Étrangleur avec Clapet de By-Pass - flow 2-1 - 3000 psi (210 bar)
FPBM FLeX Series pilot-operated, Normalement Ouvert , électro-proportionnel Étrangleur - flow 2-1 - 3000 psi (210 bar)
FPBN FLeX Series pilot-operated, Normalement Ouvert , électro-proportionnel Étrangleur avec Clapet de By-Pass - flow 2-1 - 3000 psi (210 bar)

Retour Vers le Haut

Ressources Complémentaires [ + ]

A la Une de Sun

Informations et Conseils Techniques Pour les Differentes Fonctions Hydrauliques SUN